ICOM 200 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro ne ICOM 200. Icom 200 User's Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - 200/201/241

ICOM® 200/201/241

Strany 2

ICOM-manual First steps Power supply The ICOM-200/201 uses a power supply with 8-12 VDC, 1A. Minus is placed on the pin of the power supply connector.

Strany 3 - Register

ICOM-200 / 201 RUN mode If the DIP-switch “PC/Run” is in position “Run”, the program in the ICOM-200/201 is executed immediately after a reset. Debu

Strany 4

ICOM-manual SLEEP mode The ICOM-200/201 can be put into sleep mode if the Tiny-Tiger® inside has a real time clock. In sleep mode the power consumptio

Strany 5 - Contents

ICOM-200 / 201 2 To put the ICOM-200/201 into sleep mode, the alarm time for the Tiny-Tiger® clock has to be set. Following that the ICOM-200/201

Strany 6

ICOM-manual Keyboard The ICOM-200 has a 20 key matrix keyboard. The keyboard is devided into two blocks. The first block has four vertically arranged

Strany 7 - 1 About this manual

ICOM-200 / 201 '-------------------------------------------------------------------- '----- ICOM_KEYB.TIG '--------------------------

Strany 8

ICOM-manual LC display The ICOM-200 has a graphic LC display with a resolution of 128 x 64 pixel. There’s a special device driver to control this dis

Strany 9 - 2 ICOM-200 / 201

ICOM-200 / 201 Serial Interface As a standard the ICOM-200 and ICOM-201 have two serial interfaces. From these the port Ser0 can by choice be config

Strany 10 - First steps

ICOM-manual The pins of serial port 0 are located on the DB-37 connector: RS232 DB-37 TXD0 (Output) 16 RXD0 (Input) 17 RTS0 36 CTS0 35 2 RS485 The

Strany 11 - Program download

ICOM-200 / 201 Opto inputs The ICOM-200/201 has eight optocoupler inputs suited for an input voltage range of 5...12 VDC. To use higher input voltag

Strany 13

ICOM-manual '-------------------------------------------------------------------- '----- ICOM200_OPTOIN.TIG '--------------------------

Strany 14 - Keyboard

ICOM-200 / 201 Power outputs The power outputs of the ICOM-200/201 are extended outputs of the Tiny-Tiger®, which are equiped with a driver IC type

Strany 15

ICOM-manual '-------------------------------------------------------------------- '----- ICOM200_OUTPUTS.TIG '-------------------------

Strany 16 - LC display

ICOM-200 / 201 Analog inputs The analog inputs have a hardware resolution of 10 bit, nevertheless by software interpolation a resolution of 12 bit c

Strany 17 - Serial Interface

ICOM-manual The configuration is done with jumpers on the backside of the board (see picture). To alter the configuration it is neccessary to open the

Strany 18 - ICOM-manual

ICOM-200 / 201 Configuration 0…10V To use the analog inputs with voltages of up to 10V DC, it is neccessary to change the jumper configuration. Plea

Strany 19 - Opto inputs

ICOM-manual Setting the amplification The analog inputs of the ICOM-200 / 201 have an adjustable input amplifier. The amplification can be set to a fa

Strany 20

ICOM-200 / 201 '-------------------------------------------------------------------- '----- ICOM200_AD.TIG '-------------------------

Strany 21 - Power outputs

ICOM-manual MF-2 Keyboard The ICOM-200 and ICOM-201 both have a connector for a MF2 keyboard. With this it is possible to connect a common PC keyboard

Strany 22

ICOM-200 / 201 '-------------------------------------------------------------------- '----- ICOM200_MF2.TIG '------------------------

Strany 23 - Analog inputs

About this manual 1 ICOM-200 / 201 2 ICOM-241 3 Advice and support 4 Register 5

Strany 24 - Configuration 0...5V

ICOM-manual CALL SetLcdOutputPos( LCD, 9, 0 ) PRINT_USING #LCD, wKey BITAND 0ffh CALL SetLcdOutputPos( LCD, 9, 1 ) PRINT_U

Strany 25 - Configuration 0...20mA

ICOM-200 / 201 2 ENDIF ENDWHILE END SUB SetLcdOutputPos( WORD wDevId; BYTE Column, Row ) PRINT #wDevId, "<1BH>A";CHR$( C

Strany 26 - Setting the amplification

ICOM-manual TINY-Tiger® Pins The ICOM-200/201 has, in addition to the extended I/O pins with optocouplers and transistors, some standard pins of the T

Strany 27

ICOM-200 / 201 Technical data LCD: Graphical display with 128 x 64 pixel and LED backlight. 2 Keyboard: Keyboard matrix with 20 keys and addition

Strany 29

ICOM-241 3 ICOM-241 The ICOM-241 is the most cost effective solution of the ICOM family. The processor used is a Tiny-Tiger® Economy. The ICOM-241 ha

Strany 30

ICOM-manual First steps Power supply The ICOM-200/201 uses a power supply with 8-12 VDC, 1A. Minus is placed on the pin of the power supply connector.

Strany 31

ICOM-241 RUN mode If the DIP-switch “PC/Run” is in position “Run”, the program in the ICOM-241 is executed immediately after a reset. Debugging is no

Strany 32 - TINY-Tiger

ICOM-manual Opto inputs The ICOM-241 has eight optocoupler inputs suited for an input voltage range of 5...12 VDC. To use higher input voltages, as 24

Strany 33 - Technical data

ICOM-241 '-------------------------------------------------------------------- '----- ICOM241_OPTOIN.TIG '----------------------------

Strany 34

Copyright © by Wilke Technology GmbH Krefelder Str. 147 52070 Aachen / Germany manual version 1.4 This manual, together with the hardware and sof

Strany 35 - 3 ICOM-241

ICOM-manual Power outputs The power outputs of the ICOM-241 are extended outputs of the Tiny-Tiger® Economy, which are equiped with a driver IC type T

Strany 36

ICOM-241 Serial interface As a standard the ICOM-241 has two serial interfaces. From these the port Ser0 can by choice be configured as RSR232 or RS4

Strany 37 - ICOM-241

ICOM-manual The pins of serial port Ser0 are located on the DB25 connector. The pin layout is shown in the table below: 3 RS232 Pin DB25 socket TxD0

Strany 38

ICOM-241 Placing or removing of the ICs is only allowed without power supply. ! RS485 Pin DB25 socket TXD0 (A) 18 RXD0 (B) 17 Layout of DB25 socke

Strany 39

ICOM-manual '-------------------------------------------------------------------- '----- ICOM200_RS232.TIG '---------------------------

Strany 40

ICOM-241 Analog inputs The analog inputs of the ICOM-241 have an input range from 0...5V DC. The hardware resolution is 10 bit and can be raised to 1

Strany 41 - Serial interface

ICOM-manual 3 ICOM-manual 3-12 Wilke Technology GmbH • 0241/918900 • http://www.wilke.de/ • [email protected] 3 Circuit of analog inputs 3-12 Wilke Tec

Strany 42

ICOM-241 '-------------------------------------------------------------------- '----- ICOM200_AD.TIG '--------------------------------

Strany 43

ICOM-manual Pin layout 25-pin D-Sub connector The 25-pin D-Sub connector carries all available I/O pins (except for serial port 0) of the ICOM-241. 3

Strany 44

ICOM-241 Technical data Interface: 1 x RS232 1 x RS232/RS485 selectable. Analog In: 4 x 0...5V with input amplifier 1 < V < 10 Resolutio

Strany 45

Contents Contents 1 About this manual 1-1 Typographic conventions and symbols 1-2 2 ICOM-200 / 201 2-1 Versions 2-1 Differences between ICOM-200

Strany 46

ICOM-manual ICOM 241 – 24V The ICOM-241 – 24V is a variant of the ICOM 241. It needs a supply voltage between 14V and 24V DC. The serial port SER1 is

Strany 47

ICOM-241 Connection to PC For programme download, debugging and other communication with a PC use a crosslinked cable (null modem) Technical data

Strany 49 - Technical data

Hints and Help 4 Hints and help When you have problems with a Tiger-BASIC® program: Try to reduce the problem to a short and simple sample progr

Strany 50 - ICOM 241 – 24V

ICOM-manual 4 4-2 Wilke Technology GmbH • 0241/918900 • http://www.wilke.de/ • [email protected]

Strany 51

Index 5 Register Amplification 2-18 analog inputs 2-15, 3-12 Display 2-8 Goldcap 2-4 I/O pins 2-24 ICOM-241 3-1 LC display 2-8 Loading time 2

Strany 52

Contents Opto inputs 3-4 Power outputs 3-6 Serial interface 3-7 RS232 3-7 RS 485 3-8 Analog inputs 3-11 Pin layout 25-pin D-Sub connector 3-14 T

Strany 53 - 4 Hints and help

General 1 About this manual 1 This manual does introduce you into the control of the ICOM industry computer family for a fast and easy use. The ICO

Strany 54

ICOM-manual 1 Typographic conventions and symbols Following fonts and symbols are used for fast identification of important informations: Element Mea

Strany 55 - 5 Register

ICOM-200 / 201 2 ICOM-200 / 201 Versions 2 This manual describes the ICOM200 and ICOM201 til version V1.3. Newer versions are described in separate

Komentáře k této Příručce

Žádné komentáře